Features

Smooth connection/disconnection

During connection and disconnection, the valve is closed, enabling smooth connection/disconnection under zero line pressure.

Connection A smooth push-to-connect operation without load (zero line pressure).	Disconnection The residual pressure in the plug side is purged by operating sleeve (B), enabling smooth disconnection without load (zero line pressure).
Connection movie	Disconnection movie

Built-in valve

The valve can be opened and closed while the socket and plug are connected.

Connection A safety design that prevents air from flowing by locking the sleeve (B) when the plug is not connected. After the plug is connected, slide the sleeve (B) to open the valve.

Disconnection A safety design that allows disconnection of plug, only when the valve is closed. The sleeve (A) will not operate unless the valve is closed by operating sleeve (B). 1. Pull sleeve (B) and the residual pressure in the plug side will be released.。 2. By pulling sleeve (A) the plug will disconnect.

Sleeve lock function

Prevents unintended valve operation and disconnection by locking the sleeve.

Residual pressure purge function

The residual pressure will be purged when the valve is closed.

High flow rate, low pressure loss

Unique valve mechanism prevents pressure loss and enables high flow rate.
FULL BLOW CUPLA keeps the pressure loss at the minimum level, increasing the flow rate by 40% of that of conventional HI CUPLA.
*Primary pressure: 0.6 MPa (at open air) reference data

Lightweight

The weight is reduced by 30 to 45% compared with that of conventional Cuplas. (HI CUPLA)

Specifications

Body material		Aluminum alloy
Size	Thread and hose barb	1/4", 3/8", 1/2"
	SN type	For ø6.5 mm x ø10 mm, ø8 mm x ø12 mm polyurethane hose For ø8.5 mm x ø12.5 mm, ø11 mm x ø16 mm polyurethane hose
Pressure unit		MPa	kgf/cm2	bar	PSI
Working pressure *1		1.5	15	15	218
Seal material Working temperature range *2		Seal material	Mark	Working temperature range	Remarks
		Nitrile rubber	NBR (SG)	-20 ̊C to +60 ̊C	Standard material
Suitability for Vacuum		Not suitable for vacuum application in either connected or disconnected condition.
Interchangeability		Can be connected with plugs for HI CUPLA Models 10, 17, 20, 30, and 40. Interchangeable with all other HI CUPLA Series products. Please see the page for “HI CUPLA Series Interchangeability.” Not interchangeable with some plugs of plastic HI CUPLA 250 (discontinued product).

Model	Application (Hose)	Mass (g)	Dimensions (mm)
			L	A	øT	øB
FBH-20SH	1/4"	70	(77)	30	9	5.5
FBH-30SH	3/8"	74	(81)	34	11.3	8
FBH-40SH	1/2"	85	(83)	36	15	10

Model	Application	Mass (g)	Dimensions (mm)
			L	H(WAF)	T	øB
FBH-20SM	Rc 1/4	71	(62)	Hex.22	R 1/4	8
FBH-30SM	Rc 3/8	75	(62)	Hex.22	R 3/8	11
FBH-40SM	Rc 1/2	86	(66)	Hex.22	R 1/2	15

Model	Application	Mass (g)	Dimensions (mm)
			L	H(WAF)	T
FBH-20SF	R 1/4	77	(54.5)	Hex.22	Rc 1/4
FBH-30SF	R 3/8	69	(54.5)	Hex.22	Rc 3/8
FBH-40SF	R 1/2	90	(61)	Hex.26	Rc 1/2

Model	Application (Hose) （mm）	Mass (g)	Dimensions (mm)
			L	H	T	øB
FBH-65SN	ø6.5 mm × ø10 mm	64	(64)	Hex.22	Hex.17	5.5
FBH-80SN	ø8 mm × ø12 mm	67	(66)	Hex.22	Hex.19	7.5
FBH-85SN	ø8.5 mm × ø12.5 mm	68	(66)	Hex.22	Hex.19	7.5
FBH-110SN	ø11 mm × ø16 mm	86	(71)	Hex.26	Hex.24	10

Safety Guide

Read without fail and observe the "Instruction sheet" that comes with the product and the "Safety Guide" page in the general Quick Connect Coupling Catalog.
*1. The normal allowable fluid pressure under continuous use.
Exceeding the working pressure may cause damage and leakage.
*2. The minimum and maximum working temperature range of the seal material used in the product.
Continuous use at the minimum or maximum temperature is not recommended. Please contact us for consultation.

Related products