Specifications  

 Electric Screwdriver
 Model     DLV04C10L-AY ı K         DLV10C10L-AY ı K    
 Torque  
   (Nm [lbf • in])
 SOFT fastening setting
 (1000min-1setting)
0.05 - 0.4 [0.44 - 3.54] 0.2 - 1.0 [1.77 - 8.85]
 SOFT fastening setting
 (600min-1setting)
0.05 - 0.35 [0.44 - 3.09] 0.2 - 0.45 [1.77 - 3.98]
 HARD fastening setting 0.05 - 0.4 [0.44 - 3.54] 0.2 - 1.0 [1.77 - 8.85]
 Free Speed
 (min-1
 SOFT fastening setting 600 - 1000 600 - 1000
 HARD fastening setting 100 - 1000 100 - 1000
 Screw Size
 (mm)
 Machine screw 1.2 - 3.0 [0.05” - 0.12”] 1.8 - 4.0 [0.07” - 0.16”]
 Tapping screw 1.1 - 2.5 [0.04” - 0.10”] 1.6 - 3.5 [0.06” - 0.14”]
 Bit Type NK35(OD6.35 mm [1/4”] Hex. Shank)
 Input Voltage 24 V DC
 Mass 24 V DC0.37 kg [0.82 lbs]
 Rated Operation ON: 0.5 seconds / OFF: 3.5 seconds


 Controller
 Model     DCC0101X-AZ ı P    
 Input Voltage AC100 - 240 V AC, 50/60Hz
 Operation ChannelFunction   Torque and speed setting in 4-channel memory
Can switch to any operation channel
 Count Function Tracks screws fastened
Workpiece detector can be incorporated
 External Start upControl Function Start up control can be enabled by external input signal
 Input Signal Method Photocoupler input
(24 V DC drive (5 mA/1 input), respond to PNP output)
 Output Signal Method Photocoupler output
(30 V DC or less, 30 mA/1 output or less, PNP output method)
 Service Power Source 24 V DC (Maximum capacity 200 mA)
 Power consumption When on standby: 20 W
During electric screwdriver rotation (rated): 30 W
 Mass 1.1 kg [2.4 lbs]
 Power cord (Optional) DLW9220 / DLW9240 / DLW9250


 Torque Measuring Equipment
 Torque Checker DLT1173A
 Measurement bit NK35 (No.2 x 4 x 75)
• For the bit tip shape, use “+No.2”  
 Screw Joint for SOFT Fastening Setting*     DLW4540(with white rubber)          DLW4550(with black rubber) 
 Screw Joint for HARD Fastening Setting DLW4560 (with metal washer)

* Please use white rubber for DLV04C10L-AZ, black rubber for DLV10C10L-AZ measurement.

Caution
· Speed and torque differs depending on the temperature. (Use within the range of +10 to +40 ℃.)
· Do not retighten screws that are already tightened. The torque will become larger than the set torque.
· Please purchase the power cord for the controller separately (see page 5).
· For torque measurements, please use Nitto Kohki's torque checker and screw joint (optional accessories). 

External dimensions                                           (Unit : mm)
・DLV04C10L / DLV10C10L
外観図-1.ai
・DCC0101X
外観図-2.ai

LED Display of Electric Screwdriver and Controller
・Notifies the OK or NG operation and settings by the LED lighting or blinking.
本体&コントローラLED表示.ai
・The status and setting content are displayed in the controller LCD.
LCD表示.ai

contents_border_ft.png